三星贴片机CP45 MMI 软件版本升级更新细节

CP-45 MMI DVT/Release Log
Date	MMI	VME	Vision	Optimizer	IT Feeder	Mark3 TSG		비 고
						한글	영문
2003/8/28	2.467	3.350	4.000	5.050	1.400	2.101	2.101
2003/9/3	2.468	3.350	4.000	5.050	1.400	2.101	2.101
2003/9/15	2.470	3.370	4.000	5.050	1.400	2.101	2.101	Release
2003/10/10		3.371						M2470SP1
2003/10/24	2.470							중국어 버전
2003/10/24		3.373						M2470SP2
2003/11/12		3.374						M2470SP3
2003/12/2		3.375
2003/12/12		3.376
2003/12/15		3.377						M2470SP4
2003/12/16			4.030					M2470SP5
2004/2/10		3.378						M2470SP6
2004/2/20		3.377	4.040					M2470SP7
2004/3/16		3.379	4.040					M2470SP8
2004/3/19		3.380
2004/4/7		3.381						M2470SP10
2004/4/16	2.474	3.400	4.051	5.057	1.600	2.101	2.101	CONFIG_MAX_TAPETYPE  변경
2004/5/12	2.482	3.450	4.051	5.057	1.600	2.101	2.101	IT Feeder Upgrade
2004/7/8	2.483	3.490	4.061	5.057	1.610	2.101	2.101
2004/9/1	2.500	3.530	4.062	5.060	1.611	2.101	2.101	Release
2004/10/5		3.531						M2500SP1
			4.100
2004/12/7		3.540						SAMEX요청사항 대응
2005/3/28		3.550						M2500SP2

VME Ver 3.371   From Ver 3.370	Date : 2003/10/10
Changed item	Class	Detail No	Detailed contents	Remarks
At  placing Seq, the Z axis TimeOut function is strengthened.			Corrected the  error that Timeout has not been made at motor alarm while placing, which  occurred at factory #1.
VME Ver 3.373   From Ver 3.371	Date : 2003/10/24
Changed item	Class	Detail No	Detailed contents	Remarks
The 회피 speed is  changed to solve the noise of Y axis at low speed.	Correction		In  case of 300~400 range, the speed 300 to 400 is changed.
VME Ver 3.374   From Ver 3.373	Date : 2003/11/12
Changed item	Class	Detail No	Detailed contents	Remarks
Error code information is added.			<60b1>  As the illumination is turned off, the presence of nozzle can't be checked.  The function to display the error head No is added.
Illumination check function is complemented when checking the  presence of vision nozzle.			To  redece the <60b1> error by use of Software as checking the illumination  along with checking the presence of vision nozzle, the sequence is correced  that the area will be checked again in case of illumination check NG. (If it  is NG even after checking 2 times, it will be treated as error.)
Check area display function is added to set at debug constant  when checking the presence of vision nozzle.			Debug  Constant 55 : VIS_NZ_CHK_DISPLAY     0 : Not displayed(default), 1 : Displayed
At  placing Seq, the Z axis TimeOut function is strengthened.			Corrected the  error that Timeout has not been made at motor alarm while placing, which  occurred at factory #1.
VME Ver 3.375   From Ver 3.374	Date : 2003/12/02
Changed item	Class	Detail No	Detailed contents	Remarks
Corrected to stop the feeder by use of "Freeze Stop"  when Feeder MisMatch is occurred when using IT Feeder.	Correction		In  existing version, only Warning message was displayed and the process was  continued. The error level is upgraded to Stop.
VME Ver 3.376   From Ver 3.375	Date : 2003/12/12
Changed item	Class	Detail No	Detailed contents	Remarks
Cencel the correction to stop the feeder by use of "Freeze  Stop" when Feeder MisMatch is occurred when using IT Feeder, and Trace  code is inserted.	Correction		Keep  the original concept (Requried to check and correct the MMI)
Corrected the shut-down phenomenon when homing while the door is  opened. 7 t: X. ?9 d) ]$ ]0 ^& w9 p    (OPT_DOOR_OPEN 34, Safe Guard ON)	Correction		It  will be treated as Freeze error, when homing while the door is opened.
Even when Z-alram, MMI is running.	Correction		Corrected  more precisely addition to former correction.
VME Ver 3.377   From Ver 3.376	Date : 2003/12/15
Changed item	Class	Detail No	Detailed contents	Remarks
Corrected that only one PCB will be fed on the conveyer when  bypassing on Large PCB feeder.	Correction		Operate  the bypass after setting that all the input/output buffers are not to be  used.
The channel information of No pallet error[5505] is corrected to  be displayed properly.	Correction		The  channel information has been displayed as CH0 all the time. Corrected that  the relevant channel information is to be displayed.
VME Ver 3.378   From Ver 3.377	Date : 2004/02/10
Changed item	Class	Detail No	Detailed contents	Remarks
Corrected to test the placement when reoperating after dumping  the parts in specific process (Mirae Electronics/Hwang, Seong-Beom).	Correction		Test  Code is added.
VME Ver 3.379   From Ver 3.378	Date : 2004/03/16
Changed item	Class	Detail No	Detailed contents	Remarks
(Daewoo Precision) VOC MPU STOP - Trace code is added.	Correction		Debuging  code is added to solve the problem that ANC ID is disappeared.
(Sehwang Electronics) Corrected the problem that the feeder will  be shut down when pressing feeder change while VOC auto operating.	Correction		The  phenomenon that sequence will misflow to other path while auto operation is  corrected.
VME Ver 3.380   From Ver 3.379	Date : 2004//
Changed item	Class	Detail No	Detailed contents	Remarks
Part registration number is changed from 100 to 150.	Correction		If  parts are registered upto 150 in MMI, the error that part ID was turned to 0  because of lack of VME memory space, which has been supported to 100, will be  corrected.
VME Ver 3.381   From Ver 3.380	Date : 2004/4/7
Changed item	Class	Detail No	Detailed contents	Remarks
Corrected the error occurred when the Vision is required for a  long time in Dry mode.	Correction		Corrected  the problem occurred when Vision 4.040 was applied in factory # 1.
In case SyncLoad is used, if Dump or ANC takes long time after  PCB placing, BUT UP won't occur and the feeder will be holding after PCB  arrives at Work zone. It is corrected.	Correction		Corrected  the problem occurred on Sehwang Electronics.
VME Ver 3.390   From Ver 3.370	Date : 2004/4/14
Changed item	Class	Detail No	Detailed contents	Remarks
LookAhead ANC function is added.	Addition		The  existing ANC has only the ANC information on next cycle, but LookAhead ANC  has all the ANC information from current cycle and final cycle by searching  the Preview algorithm. So the ANC carrying numbers will be reduced, and the  efficiency on actual production will be increased.     The Debug Constant 58 : ANC_SPEED_OPTI is set to 1.
Incompatible with existing MMI version due to change of head  file structure.	Correction		The  value of CONFIG_MAX_TAPETYPE is changed from 16 to 64.
VME Ver 3.420   From Ver 3.390	Date : 2004/5/6
Changed item	Class	Detail No	Detailed contents	Remarks
Lamp Blink problem in case of LOT Tracking part shortage is  solved.	Correction		The  lamp is set to blink in case of part shortage, however, it won't be blinking  in that case. It is solved.
While LOT tracking, the PCB Data won't be changed nor deleted  even though it is commended.	Correction		When  PCB Data is changed or deleted, ot stops after 1 step operation. In the first  place, it won't be operated at all, but there are problems to operate by 1  step. It should be decided if operate or not through checking the PCB data  from relevant cycle.
VME Ver 3.430, 3.440   VersionFix SKIP
VME Ver 3.450   From Ver 3.420	Date : 2004/5/10
Changed item	Class	Detail No	Detailed contents	Remarks
As the result of LotTracking DVT, NG correction	Correction		Error  Massage diverging     Whenever pressing Start button, ErrMsg will  output. , i. T& F  U# ?0 O& m1 k" {- n6 K    It is set to inform the completing point of PCB work in advance.
VME Ver 3.460   From Ver 3.450	Date : 2004/5/14
Changed item	Class	Detail No	Detailed contents	Remarks
VME is changed to alter the feeder Status Bar when homing by  buttons other than JogBox.	Correction		The  contents in DP_RAM is changed to inform the feeder status to MMI.
Immediately after booting, tower lamp is abnormally lighted up.  It is corrected. (Sabine in  America, VOC)	Correction
VME Ver 3.490   From Ver 3.460	Date : 2004/6/
Changed item	Class	Detail No	Detailed contents	Remarks
The problem that tape feeding speed gets slowers when working  the slave magazine of new non-stop tray feeder FW-20NS is solved.	Correction		The  problem that tape feeding speed gets slowers dud to communication load when  working the slave magazine on non-stop tray feeder FW-20NS is solved. (The  problem from FW-20NS field test is solved.)
The problem that excessive communication is made between tray  feeder and machine is corrected.	Correction		When  tray feeder is used, pallet out commnication is made on the cycle where the  tray part isn't used at all if Fast Pallet Change Option is used. It is  collected.
During contineous feeder change motion, it won't move at any  point, so the machine should be restarted. It is corrected.	Correction		It  is corrected that if feeder change button doesn't work, press Emergency Stop  button and than perform Homing, the it will be restarted.(DVT  No. 5)
If feeder change button is pressed during machinr running or  warm-up, it moves to Wait position and then proceeds again. It is  corrected.	Correction		It  is corrected that it won't move to Wair position even though feeder change  button is pressed during machinr running or warm-up.(DVT No. 23)
If homing at MMI while door open, error level is EMER. In case  of repeated operation, VME will be Down.	Correction		The  error level that occurred at MMI while door open is changed to Freeze. After  change, VME won't be Down.
During warm-up, JogBox is operated.	Correction		Machine  Status during WarmUp is changed to WAIT, and all the key of JogBox won't work  at all during warm up.
In case of Array PCB, if Production Range is designated, the  work is done abnormally. It is corrected.	Correction		`-  If it isn't Array PCB, the work will be done normally.     - In case of Array PCB, the work wil be done  normally when Array Extend 5 f# p5 w: \9 H6 |: u+ D  U    - In case of Array PCB, the work wil be done  normally by PCB option 6 F9 x# k4 y. }7 z0 x) M) i! J    - In case of Array PCB, the work wil be done  normally by Point option
After ConveyorTimeOut, the machine stops as running condition  when starting after stop. It is corrected.	Correction		-.  There is PCB at output step     -. Actual work is being done at Placing zone     -. PCB is stuck at input step, so it can't move to Wait zone - l. i- Z) H, Y8 S% e2 O    -. If is is stuck until actual installing is completed, or the machine  stops as running condition when starting after stop after WarningError while  moving to Wait Zone (If the PCB is removed at output step)	VOC&#51217;&#49688;&#49324;&#54637;
In case of NG as part Manual Test, only Head1 is outputted for  MMI. It is corrected.	Correction		-.  It is corrected to output the relevant head.     -. It can be normally outputted even if pick  the part by Feeder or by hand.
VME Ver 3.500   From Ver 3.490	Date : 2004/7/13
Changed item	Class	Detail No	Detailed contents	Remarks
VersionFix operation due to preparation of lower  window.
VME Ver 3.520   From Ver 3.500	Date : 2004/7/24
Changed item	Class	Detail No	Detailed contents	Remarks
Among c009 errors, code is supplemented for the suspicious case  of Conveyor work motor.	Correction		In  the machine level, it is impossible to confirm the function. It is only  possible to monitor if this phenomenon is appeared in field.
It is corrected that Feeder Change Button is operated on  ADJUST_Mode.	Correction
The Mir angle problem is corrected when the machine, whose  homing is inoperative, directoly puts into PCB manufacturing.	Correction		If  the part has large scale, it shall be opened by MirFull. However, Mir is  opened as Wait type on a specific point, so the part and Mir are contacted.  It is corrected.
While LookAhead ANC operating, unnecessary ANC operation is  performed. It is corrected(Sehwang, VOC)	Correction		During  actual installing, the unnecessary ANC is correced in case of Stop =>  Cont.
For the Door Open error and Feeder off error, debug codes are  added.	Correction		For  VOC monitoring of Samsung Electronics, VD Company
Even for the head withoug Part Pick Up, Return to Tray is  occurred when Stop->Cont. It is corrected.	Correction		It  is corrected that only the head which is picked up will try the return to  Tray when Stop->Cont. among the tray parts.
VME Ver 3.530   From Ver 3.520	Date : 2004/8/25
Changed item	Class	Detail No	Detailed contents	Remarks
If the tape feeder is placed on rear side, Left and Right are  applied reversely in SOL pattern. (Problem occurred in NS feeder)	Correction		Problem  occurred at SAMEX when NS feeder was applied.
VME Ver 3.531   From Ver 3.530	Date : 2004/10/05
Changed item	Class	Detail No	Detailed contents	Remarks
The bug related to SAMEX tray feeder is  corrected.	Correction		The  problem of pallet out in SAMEX tray feeder is corrected.
VME Ver 3.532   From Ver 3.531	Date : 2004/10/08
Changed item	Class	Detail No	Detailed contents	Remarks
Accept/Bad Mark related VOC.(Ryu, Il-sang, VOC)	Correction		If  the Accept Mark Use option is once selected, this setting condition won't be  cleared even after release, so operation is to be abnormal. It is corrected.
VME Ver 3.540   From Ver 3.530	Date : 2004/12/07
Changed item	Class	Detail No	Detailed contents	Remarks
Request by SAMEX; The function to made signal whenever operating  one piece of PCB.	Correction		Request  by SAMEX; Output to Conveyor I/F board CN13 Pin 246 whenever operating one  piece of PCB. (2 : +24V, 4:  TR O.C, 6: GND)
VME Ver 3.541   From Ver 3.540	Date : 2004/12/08
Changed item	Class	Detail No	Detailed contents	Remarks
The pallet out loading point gets slow, when working lower  magazine on non-stop tray feeder(24XS). It is corrected.	Correction		Request  by SAMEX
VME Ver 3.542   From Ver 3.541	Date : 2005/01/11
Changed item	Class	Detail No	Detailed contents	Remarks
The lower magazine pallet on non-stop tray feeder(24XS) won't be  updated. It is corrected.	Correction		Communication  protocol is added to delivery update information of lower magazine when alarm  is occurred on upper magazine so it pass to lower magazine.
VME Ver 3.543   From Ver 3.542	Date : 2005/03/10
Changed item	Class	Detail No	Detailed contents	Remarks
Factory Debug constant 27 is added. 7 s; Y) S) a; p    (LARGE_PCB_SIZE_X)	Correction		Default  : 0, If Large PCB X Size is set to more than 460mili, the relevant value will  be inputted.
VME Ver 3.550  From Ver 3.543	Date : 2005/03/28
Changed item	Class	Detail No	Detailed contents	Remarks
While actual installing, Blow is formed in the step of Vision  Nozzle Check and Vac Off after ANC, so the Pickup part is off from the PickUp  position. This error is corrected.	Correction		On  ANC, Gantry movement after Vision Nozzle Check and Blow operation. The part  off error is corrected.
If  Vision type is set to None, error displayes when gray part is dumped. This  bug is corrected.	Correction		CP55 DVT  problem porting
When rear feeder change button is pressed, machine gantry  doesn't move to Wait position. It is solved.	Correction		CP55 DVT problem porting
Post  ANC operation is corrected.	Correction		Corrected that  ANC Before PCB Load option will be applied to not noly Pre ANC but also Post  ANC operation.
In case  of manual operation, door check related function is improved.	Correction		While manual  operation(Move, Home, Feed Change), if there isn't any Area sensor and  IntLock key is Bypass, Warning message will display before performing the  operation in case of door open. The operation should not be performed.
The  suspicious item related to mirror scratch is improved.	Correction		In Part All  Dump operation, Mirro Open sequence is added before Z Up operation.
While  using non-stop tray feeder lower magazine, if pallet is replaced, tape feeder  part pick-up is in Wait condition.	Correction		Corrected to  operate as upper magazine.
Related  to mirror scratch, X3203 interrupter counter values are compared.	Correction		In X3203 comp  interrupter, counter values will be compared. (The speed may be slower.)
Home  Sequence is changed as suspicious item related to mirror scratch.	Correction		Currently  Mirror homing is performed after Z-axis homing. This sequence is changed that  ZR homing is performed after Mirror homing.
VME Ver 3.552 From Ver 3.550	Date : 2005/04/08
Changed item	Class	Detail No	Detailed contents	Remarks
Additional correction related to non-stop tray feeder operation	Correction		When  lower magazine is used, ANC wasn't operated but waited while the pallet was  replaced. It is solved.
In case of Feeder PickR interlocked head, error is corrected to  another PickR angle.	Correction		When  pickup the feeder with another PickR angle by use of interlocking head, the  moment Master Head lowers to PickUp, it moves to Slave Head's PickR value.  This error is corrected.
VME Ver 3.560 From Ver 3.552	Date : 2005/04/08
Changed item	Class	Detail No	Detailed contents	Remarks
For  PartR45, Pickup function and interlocking function are added.	Correction		In case of  PartR is 45, problem on recognition angle is solved.
It is possible to move diagonally by use of JogBox.	Correction		If  another direction key is entered while moving in a direction, it couldn't  move in diagonal direction. It is corrected.
When Cont after PCB Stop, the replacing problem is solved.	Correction		When  stopping PCB Stop while placing, in case of Pause-> Stop-> Restart  after completing the placement, it worked on the already placed board. It is  solved.
VME Ver  From Ver 3.560	Date : 2005//
Changed item	Class	Detail No	Detailed contents	Remarks
While  PCB is in OutZone, same BadMark recognition motion is contineously repeated  even after BadMark recognition for PCB not to be placed. It is corrected.	Correction		It considered  the PCB as new one, so same motion was repeated. This error is corrected.
AutoLink front/rear simultaneous function is added.	Addition		AutoLink  was possible to same side only. However, the function is added to make Auto  link possible for feeder on another side.

; R4 j6 I6 x. o- ?/ f6 v

Vision Ver 4.030 From Ver 4.000		Date : 2003/12/16
No	Changed  item	Class	Detail No	Detailed contents
1	When  fix camera recognition error is occurred when actual installing, the error  image will be stored at head No 6.	Addition		When  fix camera recognition error wss occurred when actual installing, it was  difficult to check later. So, correct that the error image will be stored at  head No 6.
2	The  BGA 3*3 recognition bug is corrected.	Correction
3	The  recognition error occurred when the chip's LeadW is 0.	Correction		When  the chip's LeadW is 0, sometimes the dark chip can't be recognized. In this  case, LeadW will be changed to 0.3 so that the chip can be recognized.
4	If  noize is present on boundary while auto-teaching, "assert faild"  error was occurred. This error is corrected.	Correction
5	If  pitch error was occurred while IC recognizing, it was treated as NG. Correct  it as retry in that case.	Correction
6	If  inputting foot as low value while IC recognizing, recognition error was  occurred. This error is corrected.	Correction
7	The  algorithm is strengthened for the case when foreign materials are attached on  nozzle while IC recognizing,	Correction
8	If  inputting lid width as low value while IC recognizing, recognition error was  occurred. This error is corrected.	Correction
9	Improve  the speed of allbody algorithm.	Correction		When  the body around lid was seem to white (ex, power connector of celluar phone),  the time to recognize the allbody took long. It is improved.
10	If  specific camera was outputted while actual installing, the screen was  cropped. This problem is corrected.	Correction		No  problem in actual working. Corrected by request of manufacturing dept.
11	Illumination  check function bug is corrected.	Correction		From  3.220 version, bug is present on illumination check function (necessary for  assembling the machine). It is corrected.
Vision Ver 4.040  From Ver 4.030		Date : 2004/02/20
No	Changed  item	Class	Detail No	Detailed contents
1	When  checking the nozzle, sometimes grap was failed. It is corrected to retry In  this case.	Correction
2	BGA  recornition is improved.	Correction		Check  function is strengthed In case of noise on outside.
3	IC  recognition error message is improved.	Correction		Different  error message was displayed in case of recognition failure. It is corrected.
Vision Ver 4.051  From Ver 4.040		Date : 2004/05/03
No	Changed  item	Class	Detail No	Detailed contents
1	The  recognition is improved when lid seems to be black.	Correction		When  operating the parts with shining lid (espcialy SOP) by use of Fly camera,  recognition error was occurred as the lid seemed to be black. It is improved  by correction of algorithm.
2	The  recognition is improved when only one lid is present.	Correction		When  the only one lid was present, recognition error was occurred as the pitch was  set to 0. It is corrected.
3	If  part ID is duplicated, alarm message will be displayed.	Addition		Among  the PCB files which was made by old version OLP, some files have improper  part ID. If these files are to be downloaded, alarm message will be displayed  on screen.
Vision Ver 4.060  From Ver 4.051		Date : 2004/05/28
No	Changed  item	Class	Detail No	Detailed contents
1	The  recognition is improved when noize is present around part.	Correction		A  part of lid detection algorithm is corrected to have resistance against noise  so that the recognition rate will be increased.
2	Cancel  the correction that if part ID was duplicated, alarm message was displayed.  -> The existing users have lots of complaint.	Correction		Cancel  the correction in 4.051 version. The existing users have lots of complaint as  alarm message will be displayed when part ID is duplicatedID
Vision Ver 4.061  From Ver 4.060		Date : 2004/07/08
No	Changed  item	Class	Detail No	Detailed contents
1	Restore  the cancelled corrected in 4.060 version. (Alarm in case of part ID  duplication)	Correction		When  alarm is occurred, OLP team will take proper measures.
Vision Ver 4.062  From Ver 4.061		Date : 2004/07/19
No	Changed  item	Class	Detail No	Detailed contents
1	Recognition  error when actucal placing of Rect2 fiducial is corrected.	Correction		SW  Bug
Vision Ver 4.063  From Ver 4.062		Date : 2004/11/01
No	Changed  item	Class	Detail No	Detailed contents
1	Tail  fiducial recognition function is added.	Addition		The  function to recognize the fiducial which has tail on circual body, by request  of MFS in China.
Vision Ver 4.064  From Ver 4.063		Date : 2004/11/29
No	Changed  item	Class	Detail No	Detailed contents
1	The  bug that it can't recognize at SOP specific angle is corrected.	Correction		Correct  the bug.
2	The  function to check LED turn-over is added.	Addition		At  present, the area margin value(ExParam[30]) is temporalily used.
Vision Ver 4.100  From Ver 4.064		Date : 2004/12/04
No	Changed  item	Class	Detail No	Detailed contents
1	The  function to check LED turn-over is corrected. # U: |, C4 i4 H; r' ?    (Match the interface with MMI 2600)	Correction

	MMI Ver 2.470	Date : 2003/9/15
As the Config.DB has been revised after 2.411  version, the ConfigAdd.txt should be added if upgrading from former Version.
The System file is revised in 2.453 version, so  never copy the System file in this version into the one in lower version.
No	Changed item	Class	Detail No	Detailed contents	Remarks
1	Release as the MMI Ver 2.468 DVT is completed.
	MMI Ver 2.470 CHS	Date : 2003/10/24
As the Config.DB has been revised after 2.411  version, the ConfigAdd.txt should be added if upgrading from former Version.
The System file is revised in 2.453 version, so  never copy the System file in this version into the one in lower version.
No	Changed item	Class	Detail No	Detailed contents	Remarks
1	Chinese version of MMI Ver 2.470
	MMI Ver 2.473	Date : 2004/4/14
No	Changed item	Class	Detail No	Detailed contents	Remarks
1	Corrected that same program  will be used for Chinese/English/Korean version by use of resouce DLL to make  the multilingual support possible.	Major		The  dat file names are corrected for each language  (hError.dat->Error_kor.dat)     Language selection item is added in Mark3 INI (Default(Korean):0,  English:1, Chinese Simplied:2) 0 c; f" h* F% V9 }' T% X2 c    Default, English item is added in Menu.
2	It is improved  that all the Array placing points will be checked for efficiency under the  state of no Array Extend. Even Array Skip, it is checked(VOC). It is  corrected.			Corrected  not to check in case of Array Skip.
3	It  is required to print the separate page from Utility Print regardless of Tape  Feeder number(EEPD, VOC).			P"Separate  Page" is added in Print menu.
4	In  case of PCB/Feeder/FeederBase Grid, 2 System Dump ix Predump for Dump combo.  Therefore, it is corrected not to be seen to users.			2  System Dump is made not to be seen to users so that it can't be set  abnormally.
5	Part  Search function is added.			In  case that a lot of part is registered, Part Search function will be added for  convenience of users. It is possible to search even though all the words  aren't be inputted.
6	When  registering Tr parts manually, Part R will be automatically registered as  90degree. However, the same part will be registered as 0degree when  additional registering after running the Optimizer. In this case the user  shall correct the value manually.			It  is improved that the once registered angle shall be kept, and the newly  registered feeder shall be registered as existing angle.
7	If  VGS card is changed while running the Mark3Tsg, TSG won't be executed.			In  case that VGA card is changed, when TsgErrorInfo.txt is executed, it will be  deleted due to 3D related internal function bug.
8	Confirm  message is added to the users of Producted Information Clear/Reset			Comfirm  message is added to the followings; # k5 ?; L- l4 X. P  H( T! P) X    Utility/Pd.Info Clear $ R9 x. Q' U. P  Y8 Z    Producted/Prodected PCBS : Q% s+ W1 w+ }+ U' G$ [: s% G    Production/Plc.Info + r: T/ Y5 X5 U, ?& C    Production/Sts.Info
9	Traceability  function for stick part is added.			Present  function is accomplished. The commentary is scheduled to progress the future  DVT along with IT Feeder when completing IT Feeder SW and Integrated Test  after 2.474 Release due to business trip of personnel in charged of IT Feeder  to Sabine in America.
10	2  Pocket Teach X, Y figure of PCB/Feeder/Tray and 4-1 Point definition are  changed.			Teach  point is moved from center to outer edge due to inconvenient teaching, in 2  Point X/Y-Axis Teaching.
11	When IT Feeder  is used, IT Feeder should have priority as sharing the DpRam area data with  FdrMonitor. However, FdrMonitor wirte first, so it is corrected.			Corrected not  to use FdrMonitor when using IT Feeder.
	MMI Ver 2.481	Date : 2004/5/10
No	Changed item	Class	Detail No	Detailed contents	Remarks
1	Traceability function is added.
2	When optimizer  is operated while running the machine, Manual fiducial screen can't be  displayed. Corrected not to operate the optimizer.
3	The  source is changed that part name will be indicated collectively in MachineIF  command in case of pick or dump when it is installed offline not on machine  (Refactoring).
4	When  detecting Partname which is in Step but not in part list(! function), it can  be detected from feederInfo made by IQ system in case of IQ Feeder.
5	It  is requested that the setting part nozzle is different from head nozzle  during VOC, the automatic ANC will be performed. It is impossible to perform  automatic ANC. Therefore, corrected to recommend proper nozzle(hole) as  opening the ANC window if the conditions are met.
	MMI Ver 2.482	Date : 2004/5/14
No	Changed item	Class	Detail No	Detailed contents	Remarks
1	Corrected  that only Cancel button is activated and OK button is inactivated when T/F  Cnt screen in running.
2	Corrected the  phenomenon that machine stands by for 1 miniute for the error occurred at MMI  homing.
	MMI Ver 2.483	Date : 2004/7/8
No	Changed item	Class	Detail No	Detailed contents	Remarks
1	In  case of Conveyor limit senser sensing error, Z axis limit error will be  displayed on TSG screen.
2	In  case of 2point teaching in the Step, if teaching on a step exceeding 100line  and then OK, the cursor will move to 100 step.
3	When  the relevant part isn't searched in Part search function, Text in Message  window will be broken.
4	2  System Dump function was corrected not to be seen, but stick feeder is  omitted.
5	It  is required to improve that the searched part in Part search function shall  be registered by double click of that part.
6	It  is improved not to operate T/F Cnt. "OK" function while running the  machine (Even if running while dialogue window is opened, it won't be  inactivated, so the operation can be done.)
7	It  is required to arrange the part data by order of nozzle registration if the  nozzle pertinent to part is recommend in case of part pick-up.
8	CA,  QA and Chuck of Align Type are deleted in New Part registration window.
9	In  Warm Up Dialog window, the machine won't stop when closing by "X"  button.
10	In  Production Range, Array input method is limited.
11	In  Production Range, Cycle Range Check method is changed.
12	In  Production T/F CNT, Empty related function button is added and edited, so  even one of the X or Y is entered, both will be treated.
	MMI Ver 2.500	Date : 2004/8/19
No	Changed item	Class	Detail No	Detailed contents	Remarks
1	When  ending, Default Language number will be written.
2	The  problem that SpLarge Nozzle isn't written on Inp file while running the  Optimizer is solved.
3	In  case of Part/Feeder Skip, the rear color of Step Skip check will be changed  to red.
4	In  case of Part/Feeder Skip, warning message will be displayed when all the  placing points are skipped when downloading just like the existing Step Skip  check.
5	When  NST Feeder is arrayed at rear, Pickup position X Offset will be reflected.
	MMI Ver 2.501	Date : 2004/10/18
	For IT, part amount per feeder  is outputted as file.			Sabine VOC
	MMI Ver 2.502~2.503	Date :  2004/11/..    - Temporal version (for  IT test)
	MMI Ver 2.504	Date : 2005/4/8
No	Changed item	Class	Detail No	Detailed contents	Remarks
1	After  Part Skip, when accepting after running the Optimizer, the Skip is checked in  Step. It is corrected.
2	Output  of structure change of used part amount per IQ System feeder     - Separation of Source for IT as separate file     - Change of LTS Board barcode info screen Icon  and location     - Change of internal communication format with  FDInfoSrv 8 p4 C( f3 w, Q5 @0 G7 Q) _    - Addition of Feeder Push count designation  (only for SM1)     - In Feederbase, corrected that the part alrealy registered on DB will be  added to part list when creating.			MainFrm_IQ.cpp,  Mark3View_IQ.cpp file is added. $ N2 [; R% }& X2 w$ t# M4 L    (When verifying the IT system for SM, punch will  be reflected.)
3	Device.mdb  is added to System Directory.			Nozzle  information is changed as Part.MDB-> Device.MDB to prevent collision of  machines due to DB copy among CP45 Neo/ FV     VOC No. 4900749
4	The  device driver for DPRAM Board is changed.			Corrected  to cope with Windows XP, Windows 2000, etc.
5	LED  turn-over detection function is added.			LED  turn-over detection information is added to Chip & X. \$ u4 s9 ?( S5 q    - To deal with Erae Electronics (Park,  Hyung-geun, Ha, Kyungho)     - Still unsettled if applying to the field
6	Corrected  that the NST 2 feeder can be changed as unit of part on Part List  screen.			NST  2 feeder is supported.
7	LED  turn-over detection function is added.			LED  turn-over detection information is added to Chip     - To deal with Erae Electronics (Park, Hyung-geun, Ha, Kyungho)     - Still unsettled if applying to the field
8	Corrected  that the NST 2 feeder can be changed as unit of part on Part List  screen.			NST  2 feeder is supported.

9 @( u8 o& X; N7 \

顶顶更健康